Oil & Gas Glossary 1.0

The weight of the drill stem that is suspended from the hook.

An instrument near the driller's position on a drilling rig that shows both the weight of the drill stem that is hanging from the hook (hook load)

A small swivel hook having a fast-operating automatic latch to close the hook opening when weight is suspended from the hook.

Position of the rig's weight indicator where hook load is zero.

To lower pipe or tubing onto a downhole tool, transferring all or part of the hook load.

A method for indicating hook load or force, read off rig's indicator; 1 point = 1,000 pounds

In sucker rod pumping, the difference between the polished rod peak load on the upstroke and the minimum load on the downstroke.

A device used in fishing for drill pipe. If the upper end of the lost pipe is leaning against the side of the wellbore, the wall hook centers it in the hole so that it may be recovered with an overshot, which is run on the fishing string and attached to the wall hook.

1. a curved steel rod on top of the swivel that resembles the handle, or bail, of an ordinary bucket, but is much larger. Just as an ordinary bucket is hung from a hook by its bail, the swivel is hung from the traveling block's hook by its bail. Sometimes, the two steel rods (the links) that attach the elevator to the hook are also called bails.

A hydraulic device connected between an engine and a mechanical load such as a compound. Torque converters are characterized by an ability to increase output torque as the load causes a reduction in speed. Torque converters are used on mechanical rigs that have compounds.

A large, hook-shaped device from which the swivel is suspended. It is designed to carry maximum loads ranging from 100 to 650 tons (90 to 590 tonnes) and turns on bearings in its supporting housing. A strong spring within the assembly cushions the weight of a stand (90 feet, about 27 meters) of drill pipe, thus permitting the pipe to be made up and broken out with less damage to the tool join threads. Smaller hooks without the spring are used for handling tubing and sucker rods. See stand and swivel.

A packer equipped with friction blocks or drag springs and slips and designed so that rotation of the pipe unlatches the slips. The friction springs prevent the slips from turning with the pipe and assist in advancing the slips up a tapered sleeve to engage the wail of the outside pipe as weight is put on the packer. Also called a wall-hook packer. See packer.

To begin to pull on a load.

To lower a load or ease up on a line.

A link and lever mechanism which is used to tighten a chain holding a load on a truck.

Chain or rope used to tie down loads of equipment, or the "boomer" used to tighten the chains.

An arbitrarily defined measure of resistance of a material to indentation under static or dynamic load

Cylindrical bars that support the elevators and attach them to the hook. Also called elevator bails.

W = calculated total static load. Also called design factor.

A cylindrical or spherical device that is affixed to the end of a wireline just above the hook to keep the line straight and to provide weight. v: to soak metal pieces in a chemical solution to remove dirt and scale from the metal's surface.

A damping apparatus used to pull tubing. The elevators latch onto the pipe just below the top collar. The elevators are attached to the hook by steel links or bails.

A rotary tool that is hung from the rotary hook and traveling block to suspend the drill stem and to permit it to rotate freely. it also provides a connection fore the rotary hose and a passageway of the flow of drilling fluid into the drill stem.

A part of the brake mechanism consisting of a flexible steel band lined with a material that grips a drum when tightened. On a drilling rig, the brake band acts on the flanges of the drawworks drum to control the lowering of the traveling block and its load of drill pipe, casing, or tubing.

One of the two valves in a sucker rod pumping system. It moves with the movement of the sucker rod string. On the upstroke, the ball member of the valve is seated, supporting the fluid load. On the downstroke, the ball is unseated, allowing fluid to enter into the production column. Compare standing valve.

A measurement of load safety for wire rope obtained by using the following formula: Safety Factor - B/W where:

A large load-bearing structure, usually of bolted construction. In drilling, the standard derrick has four legs standing at the corners of the substructure and reaching to the crown block. The substructure is an assembly of heavy beams used to elevate the derrick and provide space to install blowout preventers, casingheads, and so forth. Because the standard derrick must be assembled piece by piece, it has largely been replaced by the mast, which can be lowered and raised without disassembly.

A special coupling device inserted one or two joints above the bottom of the casing string that contains a check valve to permit fluid to pass downward but not upward through the casing. The float collar prevents drilling mud from entering the casing while it is being lowered, allowing the casing to float during its descent and thus decreasing the load on the derrick or mat. A float collar also prevents backflow of cement during a cementing operation.

An assembly of pulleys on a common framework; in mechanics, one or more pulleys, or sheaves, mounted to rotate on a common axis. The crown block is an assembly of sheaves mounted on beams at the top of the derrick. The drilling line is reeved over the sheaves of the crown block alternately which the sheaves of the traveling block, which is raised and lowered in the derrick by the drilling line. When elevators are attached to a hook on the traveling block and drill pipe latched in the elevators, the pipe can be raised or lowered. See crown block and traveling block.