Oil & Gas Glossary 1.0

A series of hydraulic rams to restrain and pull tubing under well pressure, temporarily attached to the wellhead for workover.

An electric or hydraulic pump on an accumulator that pumps hydraulic fluid under high pressure to the blowout preventers so that they may be closed or opened.

A portable mast that an be erected as a unit, usually by a tackle that hoists the wireline or by hydraulic pistons. The upper section of a telescoping derrick is generally nested (telescoped) inside the lower section of the structure and raised to full height either by the wireline or by a hydraulic system.

A device that stores hydraulic fluid under pressure in special containers and provides a method to open and close the blowout preventers quickly and reliably. Usually, compressed air and hydraulic pressure provide the opening and closing force in the unit. See blowout preventer.

See mechanical jar

1. of or relating to water or other liquid in motion.

2. operated, moved, or effected by water or liquid.

Proppants, beads, sand used in hydraulic fracturing operations.

Application of hydraulic pressure to the reservoir formation to create fractures through which oil or gas may move to the well bore.

A method of stimulating production by opening new flow channels in the rock surrounding a production well. Often call a frac job. Under extremely high hydraulic pressure, a fluid (such as distillate, diesel fuel, crude oil, dilute hydrochloric acid, water, or kerosene) is pumped downward through production tubing or drill pipe and forced out below a packer or between two packers. The pressure causes cracks to open in the formation, and the fluid penetrates the formation through the cracks. Sand grains, aluminum pellets, walnut shells, or similar materials (propping agents) are carried in suspension by the fluid into the cracks. When the pressure is released at the surface, the fracturing fluid returns to the well. The cracks partially close on the pellets, leaving channels for oil to flow around them to the well. See explosive fracturing, hydraulic fracturing.

A spherical object used to pump down the drill string or tubing to trip, release, or otherwise operate certain hydraulic-type tools.

Fracture induced by means of hydraulic or mechanical pressure exerted on the formation.

Tongs that are actuated by air or hydraulic fluid and are used for making up or breaking out sucker rods

An accessory or integral part of a packer used to limit the packer's upward movement under pressure.

A tool used to set drillable or permanent tools, such as packers, retainers, plugs; can be mechanical, electric, or hydraulic.

A small hydraulic line used to communicate fluid from the surface to a downhole tool, such as a subsurface safety valve.

Lighter-duty well maintenance than hydraulic workover, employing small OD tubing capable of descending down the production string under well pressure

A phenomenon in which a pressure concession occurs by suddenly stopping the flow of liquids in a closed container. Also called water hammer.

A hydraulically operated tool that is run in above the fishing tool and anchored to the casing by slips. It exerts a strong upward pull on the fish by hydraulic power derived from fluid that is pumped down the fishing string.

A device that increases the pressure on a fluid or raises it to a higher level. Various types of pumps include the bottomhole pump, centrifugal pump, hydraulic pump, jet pump, mud pump, reciprocating pump, rotary pump, sucker rod pump, and submersible pump

When explosives are used to fracture a formation. At the moment of detonation, the explosion furnishes a source of high-pressure gas to force fluid into the formation. The rubble prevent fracture healing, making the use of proppants unnecessary. Compare hydraulic fracturing.

A percussion tool operated mechanically to give an upward thrust to a fish by the sudden release of a tripping device inside the tool. if the fish can e freed by an upward blow, the mechanical jar can be very effective. Also called a hydraulic jar.

A hydraulic device connected between an engine and a mechanical load such as a compound. Torque converters are characterized by an ability to increase output torque as the load causes a reduction in speed. Torque converters are used on mechanical rigs that have compounds.

Fracturing a formation again. See formation fracturing, hydraulic fracturing.

An operation in which a specially blended liquid is pumped down a well and into a formation under pressure high enough to cause the formation to crack open, forming passages through which oil can flow into the wellbore. Sand grains, aluminum pellets, glass beads, or similar materials are carried in suspension into the fractures. When the pressure is released at the surface, the fractures partially close on the proppants, leaving channels for oil to flow through to the well. Compare explosive fracturing.

The force exerted by a column of liquid expressed by the height of the liquid above the point at which the pressure is measured. Although "head" refers to distance or height, it is used to express pressure, since the force of the liquid column is directly proportional to its height. Also called head or hydrostatic head. Compare hydrostatic pressure.

The cutting or boring element used in drilling oil and gas wells. This bit consists of a cutting element and a circulating element. The circulating element permits the passage of drilling fluid and utilized the hydraulic force of the fluid stream to improve drilling rates. In rotary drilling, several drill collars are joined to the bottom end of the drill pipe column, and the bit is attached to the end of the string of drill collars. Most bits used in rotary drilling are roller cone bits, but diamond bits are also used extensively.

1. to force pipe or tools into a high-pressure well that has not been killed (i.e., to run pipe or tools into the well against pressure when the weight of pipe is not great enough to force the pipe through the BOPs). Snubbing usually requires an array of wireline bocks and wire rope that forces the pipe or tools into the well through a stripper head or blowout preventer until the weight of the string is sufficient to overcome the lifting effect of the well pressure on the pipe in the preventer. In workover operations, snubbing is usually accomplished by using hydraulic power to force the pipe through the stripping head or blowout preventer.