Oil & Gas Glossary 1.0

Commonly called a "V-G meter." A rotational device powered by means of an electric motor or handcrank. Used to determine the apparent viscosity, plastic viscosity, yield point, and gel strengths of drilling fluids. See direct-reading viscometer

Commonly called a "V-G meter." The instrument is a rotational-type device powered by means of an electric motor or handcrank, and is used to determine the apparent viscosity, plastic viscosity, yield point, and gel strengths (all of which see) of drilling fluids. The usual speeds are 600 and 300 revolutions per minute. See API RP13B for operational procedures. Also see direct-indicating viscometer.

An absolute flow property indicating the flow resistance of certain types of fluids. It is a measure of shearing stress.

Commonly called the funnel viscosity. The Marsh funnel viscosity is reported as the number of seconds required for a given fluid to flow 1 qt through the Marsh funnel. In some areas, the efflux quantity is 1,000 cc. See API-RP13B for instructions. See also kinematic viscosity.

See plastic fluid

A drilling mud prepared by adding a surfactant to a water-base mud to change the colloidal state of the clay from that of complete dispersion to one of controlled flocculation. Such muds were originally designed for use in deep, high-temperature wells, but their many advantages (high chemical and thermal stability, minimum swelling effect on clay-bearing zones, lower plastic viscosity, and so on) extend their applicability.

A dilatant, or inverted plastic, fluid is usually made up of a high concentration of well-dispersed solids that exhibits a nonlinear consistency curve passing through the origin. The apparent viscosity increases instantaneously with increasing rate of share. The yield point, as determined by conventional calculations from the direct-indicating viscometer readings, is negative; however, the true yield point is zero.

Having the capability of changing apparent viscosity with a change in shear rate. Pseudoplastic fluids gain viscosity when subjected to a decrease in shear rate, and lose viscosity when the shear rate is increased. See shear.

A complex, non-Newtonian fluid in which the shear force is not proportional to the shear rate. Most drilling muds are plastic fluids.

The state in fluid dynamics of a fluid in motion is determined by the type of fluid (e.g., Newtonian, plastic, pseudoplastic, dilatant); the properties of the fluid such as viscosity and density; the geometry of the system; and the velocity. Thus, under a given set of conditions and fluid properties, the fluid flow can be described as plug flow, laminar (called also Newtonian, streamline, parallel, or viscous) flow, or turbulent flow.

The yield value (commonly called "yield point") is the resistance to initial flow, or represents the stress required to start fluid movement. This resistance is due to electrical charges located on or near the surfaces of the particles. The values of the yield point and thixotropy, respectively, are measurements of the same fluid properties under dynamic and static states. The Bingham yield value, reported in lb/100 square feet, is determined by the direct-indicating viscometer by subtracting the plastic viscosity from the 300-rpm reading.

Viscosity as measured by the Marsh funnel, based on the number of second it takes for 1,000 cubic centimeters of drilling fluid to flow through the funnel.

A unit of viscosity as measured with a Marsh funnel according to API procedure. See API RP 13B, Marsh funnel viscosity.

A measure of the resistance of a fluid to flow. Resistance is brought about by the internal friction resulting from the combined effects of cohesion and adhesion. The viscosity of petroleum products is commonly expressed in terms of the time required for a specific volume of the liquid to flow through a capillary tube of a specific size at a given temperature.

A fluid in which the viscosity remains constant for all rates of shear if constant conditions of temperature and pressure are maintained. Most drilling fluids behave as non-Newtonian fluids, as their viscosity is not constant but varies with the rate of shear.

2. a batching cylinder with neoprene or plastic cups on either end and used to separate different products traveling in the same pipeline.

A device used to determine the viscosity of a substance. Also called a viscosimeter.

One-hundredth of a poise; a measure of a fluid's viscosity, or resistance to flow.

1. in drilling, a plastic mixture of cement and water that is pumped into a well to harden. There it supports the casing and provides a seal in the wellbore to prevent migration of underground fluids.

A chemical or combination of chemicals that, when added to a drilling mud, reduces its viscosity.

A flange which incorporates plastic pieces to separate the metal parts.

A metal or plastic device that is screwed onto or into pipe threads to protect 5them from damage when the pipe is not in use.

A reservoir formation in which fluid or plastic masses of rock material originated at unknown depths and pierced or lifted the overlying sedimentary strata.

An elastic material made of synthetic rubber or plastic; often the main component of the packing material in blowout preventers and downhole packers.

The reciprocal of viscosity. The measure of rate with which a fluid is continuously deformed by a shearing stress; ease of flowing.

Pertaining to packers and other tools left in the wellbore to be broken up later by the drill bit. Drillable equipment is made of cast iron, aluminum, plastic, or other soft, brittle material.

A method of improved oil recovery in which chemicals dissolved in water are pumped into a reservoir through injection wells to mobilize off left behind after primary or secondary recovery and to move it toward production wells. The chemical solution includes surfactants or surfactant-forming chemicals that reduce the interfacial and capillary forces between oil and water, releasing the oil and carrying it out of the pores where it has been trapped. The solution may also contain cosurfactants to match the viscosity of the solution to that of the oil to stabilize the solution and to prevent its absorption by reservoir rock. An electrolyte is often added to aid in adjusting viscosity. Injection of the chemical solution is followed by a slug of water thickened with a polymer, which pushes the released oil through the reservoir, decreases the effective permeability of established channels so that new channels are opened, and serves as a mobility buffer between the chemical solution and the final injection of water.

A calibrated funnel used in field tests to determine the viscosity of drilling mud.

A drilling mud to which a polymer has been added to increase the viscosity of the mud.

In drilling-fluid terminology, a chemical is any material that produces changes in the viscosity, yield point, gel strength, fluid loss, and surface tension.

Any of several substances--usually organic compounds of high molecular weight--that, when added in low concentrations to a bentonite or to certain other clay slurries, will increase the viscosity of the system. See low-solids mud.

A rotational shear viscometer used for measuring the viscosity and gel strength of drilling fluids. This instrument has been largely superseded by the direct-indicating viscometer.

A short threaded nipple screwed into the open end of the coupling and over the threaded end of casing to protect the threads from dirt accumulation and damage. It is made of steel or plastic. Also called thread protector.

2. of aggregates, subdivision of aggregates. Dispersion increases the specific surface of the particle; hence, it results in an increase in viscosity and gel strength.

A flange equipped with plastic pieces to separate its metal parts, thus preventing the flow of electric current. Insulating flanges are often used in cathodic protection systems to prevent electrolytic corrosion and are sometimes installed when a flow line is being attached to a wellhead.

A rubber-bodied, plastic- or aluminum-cored device used to separate cement and drilling fluid as they are being pumped down the inside of the casing during cementing operations. A wiper plug also removes drilling mud that adheres to the inside of the casing.

N:a unit of measure of permeability. A porous medium has a permeability of 1 darcy when differential pressure of 1 atmosphere across a sample 1 centimeter long and 1 square centimeter in cross section will force a liquid of 1 centipoise of viscosity through the sample at the rate of 1 cubic centimeter per second. The permeability of reservoir rocks is usually so low that it is measured in millidarcys.

A method of improved recovery in which steam is injected into a reservoir through injection wells and driven toward production wells. The steam reduces the viscosity of crude off, causing it to flow more freely. The heat vaporizes lighter hydrocarbons; as they move ahead of the steam, they cool and condense into liquids that dissolve and displace crude oil The steam provides additional gas drive. This method is used to recover viscous oils. Also called continuous steam injection or steam flooding.