Oil & Gas Glossary 1.0

Oil and gas production of sufficient quantity to justify keeping a well in production.

An oil or gas well the production of which is so limited in relation to production costs that profit approaches the vanishing point.

The total production of oil from a well or lease during a specified period of time.

A method of producing a well in which only production casing is set through the pay zone, with no tubing or inner production string used to bring formation fluids to the surface. This type of completion has its best application in low-pressure, dry-gas reservoirs.

Any packer designed to make a seal between the tubing and the casing during production

A method of preparing a well for production in which no production casing or liner is set opposite the producing formation. Reservoir fluids flow unrestricted into the open wellbore. An open-hole completion has limited use in rather special situations. Also called a barefoot completion.

A type of gravel pack where the wells production packer is removed and a service packer is run in with the gravel pack assembly. After packing, the service tool is retrieved and the production packer rerun.

A method of stimulating production by opening new flow channels in the rock surrounding a production well. Often call a frac job. Under extremely high hydraulic pressure, a fluid (such as distillate, diesel fuel, crude oil, dilute hydrochloric acid, water, or kerosene) is pumped downward through production tubing or drill pipe and forced out below a packer or between two packers. The pressure causes cracks to open in the formation, and the fluid penetrates the formation through the cracks. Sand grains, aluminum pellets, walnut shells, or similar materials (propping agents) are carried in suspension by the fluid into the cracks. When the pressure is released at the surface, the fracturing fluid returns to the well. The cracks partially close on the pellets, leaving channels for oil to flow around them to the well. See explosive fracturing, hydraulic fracturing.

An arrangement for producing a well in which one wellbore penetrates two or more petroleum-bearing formations. In one type, multiple tubing strings are suspended side by side in the production casing string, each a different length and each packed to prevent the commingling of different reservoir fluids. Each reservoir is then produced through its own tubing string. Alternatively, a small-diameter production casing string may be provided for each reservoir, as in multiple miniaturized or multiple tubingless completions.

A single well that produces from two separate formation at the same time. Production from each zone is segregated by running two tubing strings with packers inside the single string of production casing, or by running one tubing string with a packer through one zone while the other is produced through the annulus. In a miniaturized dual completion, two separate 4 1/2-inch or smaller casing strings are run and cemented in the same wellbore.

See production rig. Also see pulling unit.

Said of a well when it is shut in or temporarily not able to produce.

A well completed for the production of crude oil from at least one oil zone or reservoir.

1. a well drilled in an area where no oil or gas production exists.

A system of allocating production on a per well basis.

Refers to the installation of permanent equipment for the production of oil or gas.

1. a well drilled in proven territory in a field to complete a pattern of production.

A loose term used to described oil fields that produce at nearly the same rate form day to day.

The high rate of flow made by a good well right after it is drilled.

A Well drilled or completed for the purpose of supporting production in an existing field.

A group of production tanks located in a field to store crude oil.

To remove sand, scale, and other deposits from the producing section of the well to restore or increase production.

An offset heavy-wall sub in the production string for placing gas lift valves, and so on.

A string of pipe used in workover of well-servicing operations; not typically considered as production tubing.

The oil company in charge of development and production in an oilfield in which several companies have joined to produce the field.

A ported, extended production tub used as an alternative path for wireline measuring devices.

1. the activities and methods of preparing a well for the production of oil and gas or for other purposes, such as injection; the method by which one or more flow paths for hydrocarbons are established between the reservoir and the surface.

2. the system of tubulars, packers, and other tools installed beneath the wellhead in the production casing; that is, the tool assembly that provides the hydrocarbon flow path or paths.

A string of tubing used to produce the well, providing well control and energy conservation.

The upward encroachment of water into a well caused by pressure drawdown from production.

A chart made by a recording meter which shows rate of production.

A well-servicing outfit used in pulling rods and tubing from the well. See production rig.

A test of the well's producing potential usually done during the initial completion phase

The volume of liquids statistically reported as crude oil, which is produced from oil reservoirs during given period of time.

The maintenance work performed on an oil or gas well to improve or maintain the production from a formation already producing. It usually involves repairs to the pump, rods, gas lift valves, tubing, packers, and so forth

Abbreviation: polished bore receptacle, a section in the casing string to facilitate landing of the production tubing (casing).

Sealing members at the production tubing for landing inside the packer's seal bore.

Same as seal nipple assemblies.

Lighter-duty well maintenance than hydraulic workover, employing small OD tubing capable of descending down the production string under well pressure

Describes a well in which water production is increasing.

A temporary plug set of a PSA, landed in a production packer to convert it to a bridge plug.

A well completion in which the production casing is less than 4.5 inches in diameter. Compare conventional completion.

To perform one or more of a variety of remedial operations on a producing oil well to try to increase production. Examples of workover opera6tions are deepening, plugging back, pulling and resetting liners, squeeze cementing, and so on.

A hole drilled in the earth for purpose of (1) finding or producing crude oil or natural gas; or (2) providing services related to the production of crude oil or natural gas.

A retrievable receptacle anchored into the top of a production packer to land a tubing seal assembly

The first stage of oil production in which natural reservoir drives are used to recover oil, although some form of artificial lift may be required to exploit declining reservoir drives.

A tank used in the field to receive crude oil as it comes from the well. Also called a flow tank or lease tank.

A heavy, flanged steel fitting connected to the first string of casing. It provides a housing for slips and packing assemblies, allows suspension of intermediate and production strings of casing, and supplies the means for the annulus to be sealed off. Also called a spool.

Oil production in violation of state regulations or transported interstate in violation of federal regulations.

The yield of an oil or gas well; the branch of the industry that brings the oil and gas to the surface for sale. The phase of the petroleum industry that deals with bringing the well fluids to the surface and separating them and with storing, gauging, and otherwise preparing the product for pipeline. The amount of oil or gas produced in a given period.

A method of well completion in which a slotted or perforated liner, often wire-wrapped, is placed in the well and surrounded by gravel. If open hole, the well is sometimes enlarged by underreaming at the point where the gravel is packed. The mass of gravel excludes sand from the wellbore but allows continued production.

The portion of oil, gas, and minerals retained by the lessor on execution of a leases or their cash value paid by the lessee to the lessor or to one who has acquired possession of the royalty rights, based on a percentage of the gross production from the property free and clear of all costs except taxes.

The surface area overlying an oil reservoir or reservoirs. The term usually includes not only the surface area, but also the reservoir, the wells, and the production equipment.

The string of casing set in a well after the surface casing but before production casing is set. Keeps hole from caving and seals off troublesome formations. Also called protection casing.

A chemical used to lighten the water column in gas wells, in oilwells producing gas, and in drilling wells in which air or gas is used as the drilling fluid so that the water can be forced out with the air or gas to prevent its impeding the production or drilling rate.

The gathering of pressure data and fluid samples from a formation to determine its production potential before choosing a completion method. Testing tools include formation testers and drill stem test tools.

Estimates of productive capacities of crude oil developed by the American Petroleum Institute Committee on Reserves and Productive Capacity represent the maximum daily rates of production which can be attained under specified conditions on March 31 of any given year.

The production of a separate liquid phase from a mixture of gases (e.g., rain), or of a separate solid phase from a liquid solution, as in the precipitation of calcite cement from water in the interstices of rock.

A well is considered "stabilized" when, in the case of a flowing well, the rate of production through a given size of choke remains constant, or, in the case of pumping well, when the fluid column within the well remains constant in height.

A special device placed in a string of tubing that can be operated by a wireline tool to open or close orifices to permit circulation between the tubing and the annulus. It may also be used to open or shut off production from various intervals in a well. Also called circulation sleeve.

A portable servicing or workover outfit, usually mounted on wheels and self-propelled. A well servicing unit consists of a hoist and engine mounted on a wheeled chassis with a self-erecting mast. A workover rig is basically the same, with the addition of a substructure with rotary, pump, pits, and auxiliaries to permit handling and working a drill string.

A reduction in US taxes for owners of an economic interest in minerals in place to compensate for the exhaustion of an irreplaceable capital asset. This economic interest includes mineral interest, working interest in a lease, royalty, overriding royalty, production payment interest, and net profits interest.

A rigid offshore drilling platform that stands on steel caissons and is used to drill development wells. The caissons are firmly affixed to the seafloor, and the drilling and production decks are laid on top of them. The platform is used in certain arctic waters, where the caissons are needed to protect equipment from moving ice. See platform rig.

One of the two valves in a sucker rod pumping system. It moves with the movement of the sucker rod string. On the upstroke, the ball member of the valve is seated, supporting the fluid load. On the downstroke, the ball is unseated, allowing fluid to enter into the production column. Compare standing valve.

An item of production equipment used to separate liquid components of the well stream from gaseous elements. Separators are either vertical or horizontal and either cylindrical or spherical in shape. Separation is accomplished principally by gravity, the heavier liquids falling to the bottom and the gas rising to the top. A float valve or other liquid-level control regulates the level of oil in the bottom of the separator.

A means of cementing casing in a well so that the casing may, if necessary, be retrieved with minimum difficulty. A special mud, usually an oil mud, is placed in the well ahead of the cement after the casing has been set. Non-solidifying mud is used so that it does not bind or stick to the casing in the hole in the area above the cement. Since the mud does not gel for a long time, the casing can be cut above the cemented section and retrieved. Casing packs are used in wells of doubtful or limited production to permit reuse of valuable lengths of casing.

Repressuring of an oil-field to maintain original pressure. The use of water flooding or natural gas recycling during primary recovery to provide additional formation pressure and displacement energy that can supplement and conserve natural reservoir drives. Although commonly begun during primary production, pressure maintenance methods are often considered to be a form of enhanced oil recovery.

A method of improved recovery in which water is injected into a reservoir to remove additional quantities of oil that have been left behind after primary recovery. Waterflooding usually involves the injection of water through wells specially set up for water injection and the removal of water and oil from production wells drilled adjacent to the injection wells.

A substance that consists of large molecules formed from smaller molecules in repeating structural units (monomers). In oilfield operations, various types of polymers are used to thicken drilling mud, fracturing fluid, acid, water, and other liquids. See micellar-polymer flooding, polymer mud. In petroleum refining, heat and pressure are used to polymerize light hydrocarbons into larger molecules, such as those that make up high-octane gasoline. In petrochemical production, polymer hydrocarbons are used as a feedstock for plastics.

A method of improved recovery in which steam is injected into a reservoir through injection wells and driven toward production wells. The steam reduces the viscosity of crude off, causing it to flow more freely. The heat vaporizes lighter hydrocarbons; as they move ahead of the steam, they cool and condense into liquids that dissolve and displace crude oil The steam provides additional gas drive. This method is used to recover viscous oils. Also called continuous steam injection or steam flooding.

Drilling for oil or gas in an ocean, gulf, or sea, usually on the Outer Continental Shelf. A drilling unit for offshore operations may be a mobile floating vessel with a ship or barge hull, a semisubmersible or submersible base, a self-propelled or towed structure with jacking legs (jackup drilling rig), or a permanent structure used as a production platform when drilling is completed. In general, wildcat wells are drilled from mobile floating vessels or from jackups, while development wells are drilled from platforms or jackups.

The force exerted by a body of fluid at rest. It increases directly with the density and the depth of the fluid and is expressed in pounds per square inch or kilopascals. The hydrostatic pressure of fresh water is 0.433 pounds per square inch per foot of depth (9.792 kilopascals per meter). In drilling, the term refers to the pressure exerted by the drilling fluid in the wellbore. In a water drive field, the term refers to the pressure that may furnish the primary energy for production.

A method of improved oil recovery in which chemicals dissolved in water are pumped into a reservoir through injection wells to mobilize off left behind after primary or secondary recovery and to move it toward production wells. The chemical solution includes surfactants or surfactant-forming chemicals that reduce the interfacial and capillary forces between oil and water, releasing the oil and carrying it out of the pores where it has been trapped. The solution may also contain cosurfactants to match the viscosity of the solution to that of the oil to stabilize the solution and to prevent its absorption by reservoir rock. An electrolyte is often added to aid in adjusting viscosity. Injection of the chemical solution is followed by a slug of water thickened with a polymer, which pushes the released oil through the reservoir, decreases the effective permeability of established channels so that new channels are opened, and serves as a mobility buffer between the chemical solution and the final injection of water.