Oil & Gas Glossary 1.0

The joint of drill pipe that is used in hang-off operations so that no tool joint is opposite a set of preventer rams.

A Y-shaped chain used to spin up (tighten) one joint of drill pipe into another. One end of the chain is attached to the tongs, another end to the spinning cathead, and the third end left free. The free end is wrapped around the tool joint, and the cathead pulls the chain off the joint, causing the joint to spin rapidly and tighten up. After the free end of the chain is pulled off the joint, the tongs are secured in the spot vacated by the chain and continued pull on the chain (and thus on the tongs) by the cathead makes up the joint to final tightness.

An accessory to a fishing tool, placed above it. if the tool cannot be disengaged from the fish, the safety joint permits easy disengagement of the string of pipe above the safety joint. Thus, part of the safety joint and the tool attached to the fish remain in the hole and become part of the fish.

A heavy coupling element for drill pipe. It is made of special ahoy steel and has coarse, tapered threads and seating shoulders designed to sustain the weight of the drill stem, withstand the strain of frequent coupling and uncoupling, and provide a leakproof seal. The male section of the joint, or the pin, is attached to one end of a length of drill pipe, and the female section, or box, is attached to the other end. The tool joint may be welded to the end of the pipe, screwed on, or both. A hard-metal facing is often applied in a band around the outside of the tool joint to enable it to resist abrasion from the walls of the borehole.

To attach a joint of drill pipe onto the drill stem suspended in the wellbore to permit deepening the wellbore by the length of the joint added (about 30 feet, or 9 meters).

The entire length of all the joints of casing run in a well. Most casing joints are manufactured to specifications established by API, although non-API specification casing is available for special situations. Casing manufactured to API specifications is available in three length ranges. A joint of range 1 casing is 16 to 25 feet long; a joint of range 2 casing is 25 to 34 feet long; and a joint of range 3 casing is 34 to 48 feet long. The outside diameter of a joint of API casing ranges from 4 1/2 to 20 inches.

The act of ensuring that a pipe ram preventer will not close on a drill pipe tool joint when the drill stem is stationary. A pup joint is made up in the drill string to lengthen it sufficiently.

Pipe in which the outside diameter of the joint is the same as the outside diameter of the tube. Pipe may also be internally flush-joint.

A casing in which the outside diameter of the joint is the same as the outside diameter of the casing itself.

1. the male section of a tool joint.

The female section of a connection. See tool joint.

A heavy wall sub placed opposite flowing perforations.

To loosen a tight joint as in line pipe or sucker rods.

A joint of drill pipe. Compare double, thribble, and fourable.

The heaviest-wall casing section of the string, usually located just below the preventers or tree.

A length of drill or line pipe, tubing, or casing considerably shorter than 30 feet.

A cutoff pup joint below a packer used as a fluid entry device and/or seal assemblies guide

A pinned-end pup joint used to provide additional length and inside diameter necessary to accommodate a standard milling tool.

A sub with a telescoping joint used in dual or triple completions for running additional tail pipe.

A device used with slips to prevent tubing from falling into the hole when a joint of pipe is being unscrewed and racked.

A device used to connect long lines of pipe to allow the pipe joints to expand or contract as the temperature rises or falls.

A tubing sub made of abrasion-resistant material. It is used in a tubing string where high-velocity flow through perforations may cause external erosion.

A special type of flanged connection in which a metal ring (resting in a groove in he flange) serves as a pressure seal between the two flanges.

A single length (30 feet or 9 meters) of drill pipe, drill collar, casing, or tubing that has threaded connections at both ends. Several joints screwed together constitute a stand of pipe.

A length of casing with one thread on the field end and a different thread in the coupling, used to make a changeover from one thread to another in a string of casing.

A screen joint placed opposite perforations in sand control

A hollow, rubber-faced cylinder mounted on a hollow mandrel with a pin joint on the upper end to connect to the swab line. A check valve that opens upward on the lower end provides a way to remove the fluid from the well when pressure is insufrficien5t to support flow.

An essentially full-opening valve installed immediately below the kelly, with outside diameter equal to the tool joint outside diameter.

An essentially full-opening valve installed immediately below the kelly, with outside diameter equal to the tool joint outside diameter.

To screw a length of pipe into another length of pipe.

An explosive method utilizing primacord, which is an instantaneous textile-covered fuse with a core of very high explosive. It is used to create an explosive jar inside st5uck drill pipe or tubing so that the pipe may be backed off at the joint immediately above where it is stuck.

The heavy steel member, three-, four-, six-, or eight-sided, suspended from the swivel through the rotary table and connected to the topmost joint of drill pipe to turn the drill stem as the rotary table turns. It has a bored passageway that permits fluid

To pull rods and tubing from a well at the same time. Tubing must be "stripped" over the rods a joint at a time.

A logging device used to determine accurately the depth of a well; the log measures and records the depth of each casing collar, or coupling, in a well. Since the length of each joint of casing is written down, along with the number of joints of casing that were put into the well, knowing the number and depth of the collars allows an accurate measure of well depth

To release pipe that is stuck in the hole by running washover pipe. The washover pipe must have an outside diameter small enough to fit into the borehole but an inside diameter large enough to fit over the outside diameter of the stuck pipe. A rotary shoe, which cuts away the formation, mud, or whatever is sticking the pipe, is made up on the bottom joint of the washover pipe, and the assembly is lowered into the hole. Rotation of the assembly frees the stuck pipe. Several washovers may have to be made if the stuck portion is very long.